Baaaaad ass ...
Printable View
Baaaaad ass ...
thanks guys,
fast forward to october, played around with the idea of picking up a 69 C10 with a turbo LS 76mm but talked myself out of it. I had even scored a VVT 2010 6.0L ( LQ9 ) fon the CHEAP and bought a set of 317 heads but i sold everything off though.
http://i223.photobucket.com/albums/d...ps8719ab69.jpg
http://i223.photobucket.com/albums/d...ps402b7160.jpg
http://i223.photobucket.com/albums/d...psd7221434.jpg
http://i223.photobucket.com/albums/d...ps678edab0.jpg
http://i223.photobucket.com/albums/d...psd11d7a02.jpg
http://i223.photobucket.com/albums/d...ps52fb70c2.jpg
http://i223.photobucket.com/albums/d...psd29dbb92.jpg
http://i223.photobucket.com/albums/d...ps378354ab.jpg
a customer at my job welded everything up for me for $20, i used a magnaflow Y- pipe with dual 2.5" inlets to a single 3" to the T4 twin scroll flange
http://i223.photobucket.com/albums/d...pscacb48aa.jpg
http://i223.photobucket.com/albums/d...ps855dea29.jpg
also scored a really good deal on a Holley corvette LS2 serpentine setup, so i switched over to Vette accessories, it fits like it was made for an S10/ G Body swap in general!
http://i223.photobucket.com/albums/d...psa9dfcc08.jpg
http://i223.photobucket.com/albums/d...pscd640d24.jpg
http://i223.photobucket.com/albums/d...pscc26190f.jpg
Looks good keep updating!
I actually removed everything this week and changed my setup quite a bit. I went with a 304 stainless pipe with a stainless steel v band for easy removal and adjustment of the entire hotside.
I had everything tig welded and I relocated my wastegate on the side of the pipe. Everything looks like shit because I have the bed off which I'm cutting a large access panel in. I don't plant on hauling anything so I have nothing to lose.http://i223.photobucket.com/albums/d...ps67nq7fd0.jpghttp://i223.photobucket.com/albums/d...psq89llvbe.jpghttp://i223.photobucket.com/albums/d...pspyku7egc.jpg
http://i223.photobucket.com/albums/d...psab9rf3k9.jpghttp://i223.photobucket.com/albums/d...psd3q2flch.jpghttp://i223.photobucket.com/albums/d...pst83vxvp0.jpg
lot of nice work.
I built a my rear mount setup for my ranger. The AIT temps will be lower at cruise and at speed due to the rocker being exposed to the moving air. Cool project!
where did you get the Vent that goes where the oil fil cap is located? ive been searching for something like that but havent had any luck.
everything looks good but keep an eye on the boost with that wastegate on the side it might creep at low boost levels.
I ordered it off of ebay. Its an billet LS oil cap with a -10an bung on it.
Made some progress on the charge piping aswell.http://i223.photobucket.com/albums/d...pshvoelbyi.jpghttp://i223.photobucket.com/albums/d...psouhe4emg.jpg
http://i223.photobucket.com/albums/d...pspiizmfxd.jpg
Ive been making progress. Almost dyno time!! Decided to going non intercooled with E85 and a meth injection kit. Just single nozzle for now. 80lb injectors,3bar map,http://i223.photobucket.com/albums/d...pskwqj8ufk.jpghttp://i223.photobucket.com/albums/d...ps19arh5nq.jpghttp://i223.photobucket.com/albums/d...psnz1udaev.jpg