Page 1 of 8 12345 ... LastLast
Results 1 to 10 of 77

Thread: Nokooler's Foxbody

  1. #1
    Forum Member Nokooler's Avatar
    Join Date
    Jan 2009
    Location
    Mid-Michigan
    Posts
    1,110

    Default Nokooler's Foxbody

    Alrighty, I started a thread in the photo section
    http://motownmuscle.com/forums/showt...-china!!/page2

    Figured I could just put this in the project area... where it belongs.
    Pictures from my stupidity, I pulled the lower intake off with coolant in it.. Left it for a few months. It's cleaned up pretty good.
    https://www.dropbox.com/sc/40xse4p1j...nhCGNNRwjFijua

    Build as of July-2014
    Stock 302
    F303 cam
    Gt40p Heads(comp cam springs)
    Trickflow intake/Longtubes xpipe
    8.8 with rebuild posi + 4.10's
    Either going Megasquirt or Quarter horse/TunerPro

    It's went 13.59@102(street tires) and 13.2@102(slicks), just bolt ons and 3.27's through a t5.
    The machine shop will have my Gt40p's done tomorrow(7/25).. so hopefully this thing will start by next weekend.
    and btw.. I think drinking oatmeal stouts while working on this pile, is the best beer to drink!!

  2. #2
    Forum Member nitrouspete's Avatar
    Join Date
    Jan 2012
    Location
    newport, MI
    Posts
    2,337

    Default

    F cam......hope you had the pistons fly cut. im betting that the valves will touch.

  3. #3
    Club Member SuperStang90's Avatar
    Join Date
    Jun 2008
    Location
    In the garage
    Posts
    6,114

    Default

    F cam is fine with stock pistons

  4. #4
    Forum Member nitrouspete's Avatar
    Join Date
    Jan 2012
    Location
    newport, MI
    Posts
    2,337

    Default

    Quote Originally Posted by SuperStang90 View Post
    F cam is fine with stock pistons
    if you say so.....i've seen it slap on multiple cars.

  5. #5
    Forum Member nitrouspete's Avatar
    Join Date
    Jan 2012
    Location
    newport, MI
    Posts
    2,337

    Default

    i guess what i should of said......make sure you check your PTV. sorry. haha

  6. #6
    Club Member SuperStang90's Avatar
    Join Date
    Jun 2008
    Location
    In the garage
    Posts
    6,114

    Default

    I know the TW heads will clear. Not sure on an inline head though.

  7. #7
    Forum Member nitrouspete's Avatar
    Join Date
    Jan 2012
    Location
    newport, MI
    Posts
    2,337

    Default

    id say a rocker ratio could be an issue too....stay 1.6 to be safe.

  8. #8
    Forum Member
    Join Date
    Feb 2011
    Posts
    354

    Default

    F cam will clear had that in my motor with gt40 heads and stock pistons.

  9. #9
    Forum Member Nokooler's Avatar
    Join Date
    Jan 2009
    Location
    Mid-Michigan
    Posts
    1,110

    Default

    Thanks guys! I read a lot that 1.6rockers, f303 will work. I'm still going to measure ptv clearance, just because If I don't now I won't know how to do this later in life.

    My dude setup my heads for flat tappet cam .. it'll be another day or two for my heads.

    Old school guy, very knowledgeable. I trust him.
    Though not sure what to do with my old e7's ...

  10. #10
    Forum Member Nokooler's Avatar
    Join Date
    Jan 2009
    Location
    Mid-Michigan
    Posts
    1,110

    Default

    Small update, trans is coming out tomorrow, maybe that little 302.... couple of questions.

    Is the fordracing gasket kit worth it?? Or would mix/match aka felpro stuff be worth it?
    Can I gunk the whole underside of the chassis?? previous owners gaskets didnt seal and I was too dumb to take care of it.. plus time didnt allow it.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •