For all brands of cars.
Ok just picked up a 00 Jimmy 4wd. 150k miles, When the trans is cold it shifts wierd from 2000-2500 rpms. The trans starts to shift but stutters a lil and finally shifts.(takes about a half second to a second) of hesitation. Does not do it once it warms up. Im thinking about changing the fluid...
Carrie Prejean Sextape Sample. Blog dedicated to the beautiful former Miss California Carrie Prejean. Carrie Prejean Tapes, Carrie Prejean Pics and News. : Where Is Carrie Prejean Sextape, Carrie Prejean Sex Tape Binary also more: Free Carrie Prejean Sex Tape Videos, What Site Has The Carrie...
automated forex tested Realize precisely what is most effective and as well the things doesn't with foreign exchange proficient reports plus research into the most recent programs forexrobot.tv. We uncover truth currency trading software and then present to the unsuspecting consumer the thing...
I changed some things on the comet. i went to a fully built C4 and a holley 750 It is a 347 eagle kit, ported victor jr's, Ford Z cam, victor jr intake, 3800 stall and reverse valve body. Question is that its running really lean at idle i think the idle circuit is way to lean Any tricks...
Right now I'd be able to pick up a 99 v6 mustang 5 speed like REALLY cheap. Obviously the v6 is lame, so I'd want to go V8. Just curious what you guys think would be better, like a 302, or the 4.6 that would be in it if it was a gt, or ??? Also, what else would it need? Is this something that...
do i need a special spool or can i use the spool i have for general sheet metal. or do i have to TIG it. There aluminized mufflers i wanna swap into my existing cat-back, thanks
Just realized I didn't buy an O-ring when I bought a new gasket for the Ford 9". What size is the o-ring on the pinion housing?
I am planning on converting my 89 foxbody from efi to carbed 302, and I need some help. I need to figure out what all I need to get in order to do the swap. Car is currently a roller with aod trans. I know I need a carb, carb intake, distributor with vacuum advance and steel gear, and new fuel...
Is there any local ( I am at Canton/Westland) shops that can modify the PCM calibration on my '96 GM 4.3L V6? I am looking to disable the 95mph limiter and post o2 monitoring. And depending on price have a 2nd PCM flashed to a hotter WOT calibration for 91oct. I am also looking for a "Y" pipe....
Hey guys I have a 1999 Z28 Camaro, and i need to change out the trans and rear end fluid. Was wondering what is the best or recommended brand would be. Also how many quarts do I need? Thanks -Mark
Anyone ever worked on any of these engines? I'm looking at buying an escort from my buddy and he says it needs a rod bearing because it will knock a bit under load. A friend of his that does all his car repairs says that hes done them before and just pulled the pan and fished new rod bearings in....
My buddy just blew the trans in his old toyota...anyone here want some business???
looking for something in a 195/75/15 ish area. Is it OK to go get cheap radials or is it really important to get the nicer tires from say m&h or m/t that are about 2x the price. I've never run front skinny's before so I just wanted to make sure.
I am in search of a good place that can chop down a driveshaft, shorten it, and balance. The shaft on my car now was damaged during towing, and I really do not trust it in any way. I picked up another one to replace, however it is much much too long. Providing it fits in at each end, it should be...
My car went to the dyno this week for a tune and I get a call from the guy telling me that at around 5k rpms or so, my fuel pressure is dropping off from a static 58psi down to the 20s and that I need more pump. He wasnt aware that I had a full system on the car. My fuel setup currently...
Trying to help a friend here. The engine is a 2.3t, he's got spark but no fuel. Fuel pressure is good, will start if you us estarting fluid, but injectors not firing. Something makes me think the distributor, or hall effect sensor is not working, but I am not 100% sure. Engine is in a 32 Ford, has...
My bro in law was in a rush to get gas, and didnt have it all da way in "P" when he stopped and shut off the truck yesterday. When he got home, he couldnt get the tumbler turned enough to get the key out. So now the furthest it will turn is in the "ON" postion, it wont go any further than that, so...
My dad has a 2002 Chevrolet S10 with about 88,000 miles on it. We think the fuel pump has gone bad. I am seeing five volts at the pump with the key in the "on" position. Should I see 12? The relay for the fuel pump clicks, and I switched it for another with the same model number in the fuse box....
Anyone know where I can get one at? The bosch one i have now is slow and I cant wire it directly to 12v source.
My dad has a 2002 Chevrolet S10 with 88,000 miles on it. We think the fuel filter is getting plugged and starving the motor for fuel. It quit on him while driving the other day. He has also been complaining about the idle stumbling and poor fuel mileage. The issue now is we cannot get the fuel line...
There are currently 2 users browsing this forum. (1 members & 1 guests)
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
