Ask all your Chassis/Suspension related questions here.
I need to get a new set of tires for the 18's on my camaro since its lowered and they don't fit now. I was wondering if anyone has recommendations on a good tire that can be used on the street and will handle a road race track well?
how many guys on here have rolled thier wheel lips on thier mustang? i have heard use a wooden baseball bat and slowly push down on the rear some imput would great thanks in advance guys
Just curious, lets say Ive got a 4.10 and run a 28" inch tire, giving me a certain total power ratio to the pavement, what is the reasoning behind having the bigger tire when I could go with a 26" and 3.73 and still go through the traps at the same rpm? Seems as if the taller gear would be...
I need a shop referral, closer to metro airport preferred, to wrap up my suspension and brake installation. Doin' a mild pro-touring type build on a g-body. All suspension bits are installed, minus rear sway bar, but everything needs to be dialed in.
Looking for the best traction with the rims I have. I am currently running a 255/60R15 on a weld drag light. The contact patch is about 8.5 inches and when I took it for a few races last night the car couldn't hook till about halfway through third gear. I got beat by a GTP and a nearly stock 5.0...
I'm looking for a good rear end shop in SE Michigan....with reasonable prices...Looking to get 9' ends and axles installed
just wondering
i just went out to ubly this past saturday, the conditions weren't too good for racing, and that really showed in my times. i could barely get into the 1.8's for 60 foot times, my best was a 1.88. at mid michigain i've gotten consistent 1.6's, my best being a 1.63. i sprayed in thrid and fourth...
Hey guys my 83 gt T-Top has a crack in the rocker panel that pretty much has it seperated and a little into the floor . im guessing it comes from the body flexing over they years because it was like that when i got it. I dont want the car to flex and eventually bend so is it safe to place a jack...
any toughts. it on a fox body gt. my plan is to have a weekend street car and some no et drags. can i get these to set up like a drag shock or should i buy some 90/10 drag shocks. koni yellow adjustable shocks/struts.:banstick:
How much to get a frame pulled? Any recommended shops? I have a 1998 dodge 2500, hit front drivers side. frame bent at rear upper control arm mount. doors close fine windshield not cracked.
Long story short, when I get into the throttle car goes right, when I let out it straightens back out or goes to left. Car has SSM lowers, Eibach drag springs with bag, and coilovers in front. I did all the suspension at once so its hard telling what it could be. Im wondering if it has...
Is there a minimum length for the rear bars off of the main hoop? I'm working with a mid engine car and don't want to shoot through to the engine bay in the rear. Since the b-pillar in a mid engine is structural, can I tie into the b-pillar instead? ~Eric
i have two chevy exhaust manifolds that have broken studs and a egt sensor hole that needs to be welded and retap 4" over...any one work at a shop that can help or at home dont car just tell me how much and would be great if you in the macomb area...thanks motown
After some thought, I want to delete the stock ABS system in my cobra for space concerns. The whole system is in great shape but the engine bay lines will need to be reran and the ABS module deleted. Since the car is clean and the work is limited to the engine bay, what would something like this...
I am about to start my cage install and found an issue whal checking for chassis straightness. Laid down my chassis center line and took measurements from a few symmetrical checkpoints on my frame and suspension. All the measurements were equal from side to side when measuring from frame check...
Got a set of adjustable strange front shocks I'm tossing on my 89 fox with a new strut bolt kit from team z. The washers they included are about twice as thick as they need to be. Thee are getting installed on 96-04 knuckles. Anyone know?
Hey guys, I just picked up some hpm megabite jr upper and lower control arms for my 94 mustang and want to install them this weekend. The only thing holding me back is the need of new upper control arm bushings. I'm kind of lost in if I should be running oem rubber style bushings or should I order...
I have a 91 s-10 balzer 2wd 2 door with a v 8,I was wondering what's a good relacement for it,I have a 9" out of a 72 mach one but I'm not sure on width yet,let me know what you think would be a good replacement,or is there a good upgrade for the stock 7.5
going coil over Afco shocks, need to know what body length and travel shock I need and also what pound springs to use for a fox convert. I have access to a bunch of these shocks, that is why I am asking.
There are currently 2 users browsing this forum. (1 members & 1 guests)
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules
